PULSAtron® MP with Flow Verification, 14 GPD, 100 PSI, LMK3TA-VTC1
Description
- Easily integrate into automatic chemical feed systems
Pulsafeeder's digital MP series pumps feature a 6-key keypad that allows easy programming and manual control of the pump speed. The speed is adjustable from 1 stroke/hour to 125 strokes per minute.
In the external mode, the pump will accept 4-20 mA, 20-4 mA or pulse signals. The pulse signals are available in two modes: pulse divide and pulse multiply. Pulse divide allows the pump to respond with a pre-programmed number of strokes for every 1 to 999 incoming pulses. In pulse multiply mode, the pump can be programmed to stroke from 1 to 999 times for every incoming pulse. Adjust stroke length using the dial in the center of the panel.
Pump comes standard with a stop function port that allows you to automatically shut off the pump when there is no flow in the process stream or when your chemical day tank is empty. All pumps come with a signal relay port that can be used to send a signal to an autodialer or alarm panel. Pump features feed verification, an on-board display and sensor for monitoring and verifying chemical feed. If no flow is detected, the NO switch will close and display "Flow Failure." The pump will stop stroking and activate an alarm signal. All feed verification pumps have FKM seals (check chemical compatibility before ordering). Flow verification is not available on pumps greater than 100 psi.
The pump also features an interval timer which can be programmed to operate for selected run times of 1 to 999 minutes (16 hours) at selected intervals from 1 to 999 hours (41 days) at a selected stroking rate. The totally enclosed, chemically resistant housing protects pumps in the harshest environments. Encapsulated electronics and a rigid housing ensure years of precise, repeatable performance.
Pump includes: injection valve, foot valve/strainer, suction valve, discharge valve, 5-function valve, 4' of PVC suction tubing, 4' of bleed valve return tubing, 8' of polyethylene discharge tubing, and three signal cords (one for external pacing or 4-39
Use with aluminum sulfate (alum), ammonium chloride, ammonium sulfate, ferric sulfate, 37% hydrochloric acid, potassium permanganate, sodium bisulfate, and 75% sulfuric acid (call for compatibility with other chemicals). Wetted materials: head & fittings: PVC; ceramic check balls, PTFE diaphragm and PTFE seats/O-rings.
- Max GPD: 14
- PSI: 100
- Connection: 3/8"OD Tube
- Maximum Viscosity: 1000 cP
- Suction Lift: 4 ft
Product Information
- Item number
- 48787
- Brand Name
- Pulsafeeder
- Catalog Page
- 114
- Net weight
- 12
- Condition
- New
PULSAtron® MP with Flow Verification, 14 GPD, 100 PSI, LMK3TA-VTC1
- Item number
- 48787
- Brand Name
- Pulsafeeder
- Catalog Page
- 114
- Net weight
- 12
- Condition
- New
- Easily integrate into automatic chemical feed systems
Pulsafeeder's digital MP series pumps feature a 6-key keypad that allows easy programming and manual control of the pump speed. The speed is adjustable from 1 stroke/hour to 125 strokes per minute.
In the external mode, the pump will accept 4-20 mA, 20-4 mA or pulse signals. The pulse signals are available in two modes: pulse divide and pulse multiply. Pulse divide allows the pump to respond with a pre-programmed number of strokes for every 1 to 999 incoming pulses. In pulse multiply mode, the pump can be programmed to stroke from 1 to 999 times for every incoming pulse. Adjust stroke length using the dial in the center of the panel.
Pump comes standard with a stop function port that allows you to automatically shut off the pump when there is no flow in the process stream or when your chemical day tank is empty. All pumps come with a signal relay port that can be used to send a signal to an autodialer or alarm panel. Pump features feed verification, an on-board display and sensor for monitoring and verifying chemical feed. If no flow is detected, the NO switch will close and display "Flow Failure." The pump will stop stroking and activate an alarm signal. All feed verification pumps have FKM seals (check chemical compatibility before ordering). Flow verification is not available on pumps greater than 100 psi.
The pump also features an interval timer which can be programmed to operate for selected run times of 1 to 999 minutes (16 hours) at selected intervals from 1 to 999 hours (41 days) at a selected stroking rate. The totally enclosed, chemically resistant housing protects pumps in the harshest environments. Encapsulated electronics and a rigid housing ensure years of precise, repeatable performance.
Pump includes: injection valve, foot valve/strainer, suction valve, discharge valve, 5-function valve, 4' of PVC suction tubing, 4' of bleed valve return tubing, 8' of polyethylene discharge tubing, and three signal cords (one for external pacing or 4-39
Use with aluminum sulfate (alum), ammonium chloride, ammonium sulfate, ferric sulfate, 37% hydrochloric acid, potassium permanganate, sodium bisulfate, and 75% sulfuric acid (call for compatibility with other chemicals). Wetted materials: head & fittings: PVC; ceramic check balls, PTFE diaphragm and PTFE seats/O-rings.
- Max GPD: 14
- PSI: 100
- Connection: 3/8"OD Tube
- Maximum Viscosity: 1000 cP
- Suction Lift: 4 ft